Analysis of over temperature points in steam turbine insulation and optimization plan for insulation
Release Time: 2026-11-19
Share:
In the infrared temperature measurement inspection during the overhaul of thermal power plants, the overheating of steam turbine insulation is a high-frequency defect, which not only causes an increase in unit energy consumption, but also poses risks of burns and thermal radiation affecting surrounding instrument equipment. The concentrated points where the outer wall of the steam turbine is prone to overheating mainly include: the split surface of the steam turbine, the flange and support hanger area, the cylinder manhole door, the cylinder joint surface, the steam turbine exhaust pipe, the connecting pipe, the valve flange, the overlapping gap of the insulation layer, and the cracking and falling position of the outer coating layer. In addition, the corners where the steam turbine body vibrates violently, the connection position between the old and new insulation, and the infrared temperature measurement area that exceeds the standard all year round are also the main areas.
The root cause of overheating in these areas is not simply insufficient material temperature resistance, but rather special working conditions: the steam turbine continues to vibrate for a long time, and ordinary aluminum silicate and ceramic fiber blankets undergo large thermal shrinkage. After long-term operation, the blanket body shrinks and cracks appear, and heat leaks out from the cracks; The position structure of flanges and supports and hangers is complex, and irregular positions are difficult to lay, resulting in uneven thickness of insulation layer; Traditional plastering materials have poor anti vibration performance, cracking, peeling, and detachment under repeated vibration, and the insulation layer is directly exposed and unprotected; Part of the old insulation is damp and powdery, resulting in a significant increase in thermal conductivity and a decrease in insulation efficiency.
For high-risk vibration conditions such as steam turbines, Rosewool Insulation Refractory Co.,Ltd. provides a complete insulation solution, mainly promoting PLUS reinforced ceramic fiber blankets, ceramic fiber blankets, and specialized high-temperature resistant wiping fabrics, suitable for the entire scene of steam turbine bodies, connecting pipes, flange supports and hangers.
For core overheating points with strong vibration and irregular structures such as split surfaces, flanges, support hangers, and manhole doors, “ PLUS reinforced ceramic fiber blankets” are preferred. Compared to ordinary ceramic fiber blankets, PLUS blankets have been modified for tensile resistance and low high temperature shrinkage. The high temperature shrinkage rate index is strictly controlled, making them less prone to delamination and cracking under continuous vibration of the steam turbine. The blanket structure is stable, and long-term operation is less likely to cause gap heat leakage; Good flexibility, able to fit flanges and irregular surfaces, reduce overhead gaps during cutting and paving, and eliminate thermal bridges from the source.
Large area cylinder body position, combined with conventional ceramic fiber blanket layered staggered laying, layer by layer seam pressing, to avoid through seam and prevent direct heat leakage; Control the thickness of a single layer during layered construction to ensure even compression and prevent local thinning points. All insulation outer layers are uniformly made of our factory's specialized high-temperature resistant coating material for steam turbines. This coating material combines temperature resistance, vibration resistance, and wind erosion resistance, and is different from ordinary coatings. It is suitable for continuous vibration conditions of steam turbines, and is not easy to peel or fall off, forming a complete closed protective shell to isolate moisture from corroding the insulation core material and prevent the insulation material from becoming damp and ineffective.
In terms of construction control, we suggest reducing the number of vibration points and using hard insulation materials directly, with flexible fiber insulation as the main option; Anchor and tie stainless steel wire mesh and fasteners, reinforce insulation layer, and reduce the risk of vibration detachment. The entire set of materials for the solution is self-produced from the source, eliminating the need for intermediaries and offering outstanding cost-effectiveness. The thickness and structure can be customized according to the outer wall temperature and medium temperature of the unit design.
At the end of the year, power plant overhauls are concentrated, and the insulation treatment of steam turbines prioritizes the three core areas of "anti shrinkage, anti vibration, and sealed anti gap". The combination of Rosewool Insulation Refractory Co.,Ltd. PLUS reinforced blanket, ceramic fiber blanket, and special wiping fabric is selected to effectively solve the problem of infrared temperature exceeding the standard, stabilize the outer wall temperature, reduce the heat loss of the unit, and reduce the cost of repeated maintenance in the later stage.